NovaTuff PC-425 Protective Waterproof Coating
Tikweld welding supplies and services is the distributor of NovaTuff Epoxy Primer in Nigeria. NovaTuff PC-425 is tough and flexible protective coating for concrete, metal, other surfaces. NovaTuff PC-425 is a high-solids polyamide-epoxy resin used in applications where chemical and corrosion resistance is required.
Resistance:
NovaTuff PC-425 is resistant to acids, solvents, caustics, and hydrocarbons. It was developed to withstand corrosive and abrasive conditions in a variety of applications.
Application Areas:
NovaTuff PC-425 is excellent as an anti-corrosive and protective coating for fountains, tanks, pipelines, cooling towers, vats, floors, and steel or concrete structures. NovaTuff PC-425 retains a resilient body, even after final cure. It can even be used under constant spillage, immersion conditions, or highly abrasive applications.
Preparation:
Surfaces should be free of mill scale, oil, paint, films, grease, soluble salts, and other contaminants. Sand blasting to white metal is necessary in some cases. Latinate and other loosely bound materials should be removed to provide a solid bonding surface.
Concrete should be etched to provide a profile for optimal adhesion. Latinate and other loosely bound materials should be removed to provide a solid bonding surface. The preparation procedures above are general guidelines.
MIXING:
The mixing of parts A & B is very important! NovaTuff PC-425 has a (1:1) mixing ratio of 1 parts “B” to 1 part “A”. Agitate Part B separately before combining the two parts. Pour a measured amount of Part B into a clean container large enough to hold both components. Add an equal volume of Part A to Part B then continue agitation until the two components are thoroughly mixed for at least one minute per gallon. Allow idle activation for at least 10 minutes.
THINNER:
If necessary thin with Xylene for airless spray applications, thin no more than 1/2 pint per gallon. Do not add thinner until after activation is completed. Note: Thinning retards cure time and increases possibility of sag.
APPLICATION:
Brush, 3/8″ nap roller cover, or airless spray equipment may be used to apply NovaTuff PC-425. Surface configuration, weather, or area surroundings will dictate application method.
CLEAN UP:
Application equipment should be cleaned immediately with Lacquer Thinner. Use White Vinegar to clean hands and skin. Do not allow NovaTuff PC-425 to remain on tools! Once it sets and is cured, it is difficult to remove.
TESTING AND MISC:
- Colors: NovaTuff Standard Colors (Tan or Gray) Custom colors are available
- Solids Content: 83% Solids
- Compression (C579-96): 3500 psi
- Pencil Hardness (D3363): 4H – passed
- Adhesion-Pull-Off (D4541):
- Concrete: 100 % substrate failure @ 980 psi Steel: 100% adhesion failure @ 2500 psi
- Impact Resistance (D2794):
- 52 inch lbs. direct – passed
- Mandrel Bend (D522): 1/2 inch – passed
CURING TIME:
Pot Life: 1.5 hrs @ 80ºF
Mixing Ratio: 1 Part B to 1 Part A (1:1)
Drying Time: 5 hrs @ 80ºF Total Cure: 3 days @ 80ºF
SHELF LIFE AND STORAGE CONDITIONS:
NovaTuff PC-425 has a 12 month shelf life if unopened and stored between 40 degrees Fahrenheit and 90 degrees Fahrenheit. Do not allow products to freeze.
Related Article
Sodium Hypochlorite in Water Treatment: A Powerful Solution for Safe and Clean Water
Introduction to Epoxy Flooring: Benefits and Uses
Epochem Sodium Hypochlorite Disinfectant Best use
Please Contact us for product availability
